MX100TP Aim-tti MX100TP三路可編程電源
如果你感興趣的話，可以電話：0755-33217630 33217631 
產品名稱：MX100TP Aim-tti MX100TP三路可編程電源
產品型號：MX100TP
產品廠商：深圳市深東金儀器有限公司
簡單介紹
Aim-tti MX100TP三路可編程電源Bench/System DC Power Supply, Multi-Range, Digital Control Triple Outputs, 3 x 35V/3A 315W, USB, RS232, LAN & GPIB Interfaces
MX100TP Aim-tti MX100TP三路可編程電源的詳細介紹
Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP可編程直流穩壓電源：
Bench/System DC Power Supply, Multi-Range, Digital Co
The MX100T differs from most other triple output power supplies in havin
Each output features simultaneous high resolution metering, switchable remote sense, and an individual output switch.
Mixed-mode regulation To provide its impressive power density the MX series combines high frequency switch-mode pre-regulation with linear post-regulation to offer performance that comes close to that of an all-linear design.
Excellent line and load regulation is matched by low noise and good transient response.
Range switching and power co
To increase its ability to match a variety of applications, each output has more than one range.
Outputs one and two can provide 16V/6A as an alternative to 35V/3A, while output three can provide 70V/1..
When higher power is required, outputs two and three can be combined internally to provide up to 210 watts as either 35V/6A or 70V/3A from a single output. Remote co
The MX100TP incorporates USB, RS232, GPIB and LXI compliant LAN interfaces.These provide full remote co
Aim-tti MX100TP可編程直流穩壓電源：
Aim-tti MX100TP可編程直流穩壓電源：
Aim-tti MX100TP可編程直流穩壓電源：
Aim-tti MX100TP可編程直流穩壓電源：
Aim-tti MX100TP可編程直流穩壓電源：
Aim-tti MX100TP可編程直流穩壓電源：
Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP可編程直流穩壓電源：
Bench/System DC Power Supply, Multi-Range, Digital Co
-
Three high performance outputs each with full functio
nality - Range switching gives variable voltage/current combinations
- Shared power mode provides double power from a single output
- Low output noise and ripple via linear final regulation
- High setting resolution of up to 1mV and 0.1mA
- Variable OVP and OCP trips on all outputs
-
50 setting memories per output plus 50 l
inked memories -
Selec
table voltage tracking (isolated tracking) - Selectable current meter averaging
- Switchable remote sense capability
- Graphic LCD provides simultaneous output metering
-
Numeric or spin-wheel co
ntrol of all parameters -
Individual or combined output on/off co
ntrol with - programmable delay sequencing.
- 3U half-rack case for bench or rack mounting
- GPIB, RS-232, USB and LAN (LXI) interfaces (-P models)
- Duplicate power & sense terminals at rear (-P models)
MX100T and MX100TP:
- 315 watts total power
- Three outputs of equal power, each capable of 35V at 3A
- Range switching provides up to 70 volts and up to 6 amps
The MX100T differs from most other triple output power supplies in havin
Each output features simultaneous high resolution metering, switchable remote sense, and an individual output switch.
Mixed-mode regulation To provide its impressive power density the MX series combines high frequency switch-mode pre-regulation with linear post-regulation to offer performance that comes close to that of an all-linear design.
Excellent line and load regulation is matched by low noise and good transient response.
Range switching and power co
To increase its ability to match a variety of applications, each output has more than one range.Outputs one and two can provide 16V/6A as an alternative to 35V/3A, while output three can provide 70V/1..
When higher power is required, outputs two and three can be combined internally to provide up to 210 watts as either 35V/6A or 70V/3A from a single output. Remote co
The MX100TP incorporates USB, RS232, GPIB and LXI compliant LAN interfaces.These provide full remote coAim-tti MX100TP可編程直流穩壓電源：
| OUTPUT 1 | |
|---|---|
| Ranges |
Range 1 - 0V to 35V at 1mA to 3A; Range 2 - 0V to 16V at 1mA to 6A |
| Operating Mode |
Co |
| Voltage Setting | By direct numeric entry or quasi-analogue rotary wheel; resolution 1mV. |
| Current Setting | By direct numeric entry or quasi-analogue rotary wheel; resolution 1mA. |
| Setting Accuracy |
Voltage - 0.05% of reading ± 3mV; Current - 0.3% of reading ± 3mA to 3A, 0.5% of reading ± 3mA to 6A |
| Setting Stores | Up to 50 set-ups can be saved and recalled via the keyboard (or the digital interfaces on MX100TP). |
| Load regulation | <0.01% +5mV (CV mode) for any load change using remote sense. |
| Line regulation | <0.01% +5mV (CV mode) for a 10% line voltage change. |
| Ripple & Noise | Typically <0.5mV rms, <5mV pk-pk, 1mV rms max. (20MHz bandwidth). |
|
Transient Respo |
<100us to within 50mV of set level for 5% to 95% load change. |
| Over Voltage Trip | Settable 1V to 40V in 0.1V steps |
| Over Current Trip | Settable 0.1A to 7A in 0.01A steps |
| Sensing |
Selec |
| OUTPUT 2 | |
|---|---|
| Ranges |
Range 1 - 0V to 35V at 1mA to 3A; Range 2 - 0V to 16V at 1mA to 6A Range 3 - 0V to 35V at 1mA to 6A* (available when output 3 is disabled) |
| Operating Mode |
Co |
| Voltage Setting | By direct numeric entry or quasi-analogue rotary wheel; resolution 10mV. |
| Current Setting | By direct numeric entry or quasi-analogue rotary wheel; resolution 10mA. |
| Setting Accuracy |
Voltage - 0.1% of reading ± 10mV; Current - 0.3% of reading ± 3mA to 3A, 0.5% of reading ± 3mA to 6A |
| Setting Stores | Up to 50 set-ups can be saved and recalled via the keyboard (or the digital interfaces on MX100TP). |
| Load regulation | <0.01% +5mV (CV mode) for any load change using remote sense. |
| Line regulation | <0.01% +5mV (CV mode) for a 10% line voltage change. |
| Ripple & Noise | Typically <0.5mV rms, <5mV pk-pk, 1mV rms max. (20MHz bandwidth). |
|
Transient Respo |
<100us to within 50mV of set level for 5% to 95% load change. |
| Over Voltage Trip | Settable 1V to 40V in 0.1V steps |
| Over Current Trip | Settable 0.1A to 7A in 0.01A steps |
| Sensing | Selectable local or remote sensing. |
| OUTPUT 3 | |
|---|---|
| Ranges |
Range 1 - 0V to 35V at 1mA to 3A; Range 2 - 0V to 70V at 1mA to 1. Range 3 - 0V to 70V at 1mA to 3A* (available when output 2 is disabled). |
| Operating Mode |
Co |
| Voltage Setting | By direct numeric entry or quasi-analogue rotary wheel; resolution 10mV. |
| Current Setting | By direct numeric entry or quasi-analogue rotary wheel; resolution 1mA. |
| Setting Accuracy |
Voltage - 0.1% of reading ± 10mV; Current - 0.3% of reading ± 3mA |
| Setting Stores | Up to 50 set-ups can be saved and recalled via the keyboard (or the digital interfaces on MX100TP). |
| Load regulation | <0.01% +5mV (CV mode) for any load change using remote sense. |
| Line regulation | <0.01% +5mV (CV mode) for a 10% line voltage change. |
| Ripple & Noise |
Typically <0.5mV rms, <5mV pk-pk, 1mV rms max. (20MHz bandwidth). 70V range - typically <1mV rms, <10mV pk-pk, 1.5mV rms max. |
|
Transient Respo |
<100us to within 50mV of set level for 5% to 95% load change. |
| Over Voltage Trip | Settable 1V to 80V in 0.1V steps |
| Over Current Trip | Settable 0.1A to 3. in 0.01A steps |
| Sensing | Selectable local or remote sensing. |
| Output Protection | |
|---|---|
| External Voltage | Output will withstand forward voltages of up to 50V (O/Ps 1 and 2) or 80V (O/P 3). Reverse protection by diode clamp, 3A max. |
| Fault Trip |
The output will be shut down if a trip co |
| Over Temperature |
Mo |
| Sense Error |
Mo |
|
Co |
|
|---|---|
| Output Terminals |
Universal 4mm safety binding posts on 19mm (0·75”) spacing at front. Screw terminals at rear (MX100TP only). Terminals can accept fixed shroud 4mm plugs, standard 4mm plugs, fork terminals and bare wires. |
| Sense Terminals | Sprung loaded screw-less terminals at front. Screw terminals at rear (MX100TP only). |
| OUTPUT ON/OFF SWITCHING | |
|---|---|
| Individual On/Off | Individual keys for each output. On state indicated by key illumination. |
| Multi-On/Multi-Off | Separate keys enable any combination of outputs to be turned on or off either simultaneously (default) or with timed delays from 10ms and 20s. Delayed operation indicated by flashing key illumination. |
| VOLTAGE TRACKING | |
|---|---|
| The power supply can be set so that the voltage of an output is automatically set equal to that of another output and tracks any changes. | |
| Tracking Modes | None, V2 tracks V1, V3 track V2, V2 and V3 both track V1. |
| SETTING MEMORIES | |
|---|---|
| Individual Output Memories: | |
| No. of Stores | 50 per output |
| Parameters Stored | Range, Set Volts, Set Current, OVP, OCP |
|
l |
|
| No. of Stores | 50 |
| Parameters Stored | Range, Set Volts, Set Current, OVP, OCP (for all three outputs) |
| METERING (each Output) | |
|---|---|
| Meter Function | 5 digit voltage and current meters (O/P 1), 4 digit voltage and current meters (O/Ps 2 & 3). Simultaneous display of actual and set values. |
| Meter Resolution | 1mV/0.1mA (O/P 1), 10mV/1mA (O/Ps 2 & 3). |
| Meter Accuracy | As per setting accuracy (CV mode). |
|
Additio |
V x A Calculated power in watts. Resolution 0.01Ohms. Accuracy 0·5% ± 3 digits |
| DIGITAL BUS INTERFACES (MX100TP only) | |
|---|---|
|
The MX100TP offers full remote co |
|
| RS-232 | Standard 9-pin D connector. |
| USB |
USB 2.0 co |
| GPIB (IEEE-488) |
The interface co |
| Ethernet (LAN) |
Standard 10/100 ba |
| LXI Compliance | LAN interface is compliant with LXI core 2011. (LXI is the abbreviation for LAN eXtensions for Instrumentation). |
| DIGITAL PROGRAMMING PERFORMANCE (MX100TP only) | ||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Programming Speed: | ||||||||||||||||||||||||||||||||||||
| Command Delay | Typically <100ms between receiving the command terminator for a step voltage change at the instrument and the output beginning to change. | |||||||||||||||||||||||||||||||||||
| Output Response: | ||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
| DRIVER SOFTWARE SUPPLIED (MX100TP only) | |
|---|---|
| IVI Driver | An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows*, HPVEE* etc. |
| USB Driver | An installation file is supplied which calls a standard Windows* USB driver. |
|
* LabView and LabWindows are trademarks of Natio * HPVEE (now Agilent VEE) is a trademark of Agilent Technologies. * USB interface is supported for Windows 2000, XP, Vista, 7 and 8 (including 64 bit versions). Windows is a trademark of Microsoft. |
|
| GENERAL SPECIFICATIONS | |
|---|---|
| Input: | |
| AC Input | 110V to 240V AC ±10%, 50/60Hz. Installation Category II. |
| Input Power | 500VA max. |
| Temperature & Environmental: | |
| Operating Range | +5oC to +40oC, 20% to 80% RH |
| Storage Range | -40oC to + 70oC |
|
Enviro |
Indoor use at altitudes up to 2000m, Pollution Degree 2. |
| Cooling | Intelligent variable-speed fans. |
| Safety & EMC: | |
| Safety | Complies with EN61010-1 |
| EMC | Complies with EN61326 |
| Physical: | |
| Size | 212 x 130 x 375mm (WxHxD) (half rack x 3U height) |
| Weight | 4.8kg (MX100T); 4.9kg (MX100TP). |
| OPTIONS: | |
| Rack Mount | 19 inch rack mount for one or two power supplies. |
相關產品
在線留言 |
